| ***Spare part*** SIMATIC DP, distributed I/O ET200X: Basic module BM143/DESINA 8DE/DA parameterizable ADDITIONAL diagnostics, inputs, Hybrid, Field bus activation, (RS485), Identification plug IP67 |
| General information |
| Vendor identification (VendorID) | 809Ah |
| Supply voltage |
| Load voltage non-switched (NS) |
| Rated value (DC) | 24 V |
| Short-circuit protection | No |
| Reverse polarity protection | No |
| Load voltage switched (S) |
| Rated value (DC) | 24 V |
| Reverse polarity protection | No |
| Input current |
| from load voltage, unswitched (NS) |
| up to 40 °C, max. | 10 A |
| up to 55 °C, max. | 8 A |
| from load voltage, switched (S) |
| up to 40 °C, max. | 10 A |
| up to 55 °C, max. | 8 A |
| Encoder supply |
| Number of outputs | 8 |
| Short-circuit protection | Yes; Electronic |
| Output current |
| up to 40 °C, max. | 1 A |
| up to 55 °C, max. | 0.8 A |
| Power loss |
| Power loss, typ. | 3.5 W |
| Hardware configuration |
| Expansion modules |
| Number of expansion modules, max. | 7 |
| — of which motor starters/frequency converters, max. | 6 |
| — of which pneumatic interfaces, max. | 6 |
| Digital inputs |
| Number of digital inputs | 8; 8 process channels, parameterization as DI/DO; 8 function channels, parameter assignment as diagnostics/NC input |
| Input characteristic curve in accordance with IEC 61131, type 2 | Yes |
| Number of simultaneously controllable inputs |
| all mounting positions |
| — up to 55 °C, max. | 8 |
| Input voltage |
| Rated value (DC) | 24 V; Input voltage for parameterized DI (Pin 4): Rated value 24 VDC, for signal "1": 13 to 30 V, for signal "0": -30 to +5 V: Input voltage for input functionality (Pin 2): Rated value 24 VDC, for signal "1": 13 to 30 VDC, for signal "0": -30 to +2 V |
| for signal "0" | -3 to +5V |
| for signal "1" | 13 to 30V |
| Input current |
| for signal "1", typ. | 5 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| — at "0" to "1", min. | 1.2 ms |
| — at "0" to "1", max. | 4.8 ms |
| — at "1" to "0", min. | 1.2 ms |
| — at "1" to "0", max. | 4.8 ms |
| Cable length |
| unshielded, max. | 30 m; for signal lines |
| Digital outputs |
| Number of digital outputs | 8; 8 process channels, parameterization as DI/DO; 8 function channels, parameter assignment as diagnostics/NC input |
| Short-circuit protection | Yes; Electronic |
| Response threshold, typ. | 1.8 A |
| Switching capacity of the outputs |
| on lamp load, max. | 10 W |
| Output current |
| for signal "1" rated value | 1.2 A |
| for signal "0" residual current, max. | 0.5 mA |
| Switching frequency |
| with resistive load, max. | 100 Hz |
| with inductive load (acc. to IEC 60947-5-1, DC13), max. | 2 Hz |
| on lamp load, max. | 1 Hz |
| Total current of the outputs (per module) |
| all mounting positions |
| — up to 20 °C, max. | 10 A |
| — up to 55 °C, max. | 5 A |
| Cable length |
| unshielded, max. | 30 m |
| Encoder |
| Connectable encoders |
| 2-wire sensor | Yes |
| — permissible quiescent current (2-wire sensor), max. | 1.5 mA |
| Interfaces |
| PROFIBUS DP |
| SYNC capability | Yes |
| FREEZE capability | Yes |
| 1. Interface |
| Protocols |
| PROFIBUS DP slave | Yes |
| PROFIBUS DP slave |
| Transmission rate, max. | 12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 12 Mbit/s |
| Services |
| — Direct data exchange (slave-to-slave communication) | Yes; Sender |
| Protocols |
| PROFIBUS DP | Yes |
| Interrupts/diagnostics/status information |
| Diagnostics function | Parameterizable |
| Alarms |
| Diagnostic alarm | Yes |
| Diagnostic messages |
| Diagnostic information readable | Yes |
| Diagnostics indication LED |
| RUN LED | Yes |
| Group error SF (red) | Yes |
| Status indicator per channel (yellow) | Yes |
| Indicator function input per channel (yellow/red) | Yes |
| Monitoring the unswitched load voltage DC 24 V-NS (green) | Yes |
| Monitoring the switched load voltage DC 24 V-S (green) | Yes |
| Potential separation |
| between the load voltages | No |
| between load voltage and all other switching components | No |
| between PROFIBUS DP and all other circuit components | Yes |
| Potential separation digital inputs |
| between the channels | No |
| between the channels and backplane bus | No |
| Potential separation digital outputs |
| between the channels | No |
| between the channels and backplane bus | No |
| Dimensions |
| Width | 175 mm; 180 when screw mounted |
| Height | 180 mm; 174 when screw mounted |
| Depth | 110 mm; 90 when screw mounted |
| Weights |
| Weight, approx. | 650 g |
| last modified: | 03/25/2019 |
