| *** SPARE PART*** SIMATIC DP, ELECTRONIC BLOCK FOR ET 200L, 8 DI/8 DO, 120V AC CAN BE PLUGGED INTO TB16L AC |
| General information |
| Vendor identification (VendorID) | 0027h |
| Usable terminal block | TB 16L AC |
| Supply voltage |
| Rated value (AC) | 120 V |
| Line frequency |
| permissible range, lower limit | 47 Hz |
| permissible range, upper limit | 63 Hz |
| Mains buffering |
| Mains/voltage failure stored energy time | 20 ms |
| Load voltage L+ |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 4.5 V |
| permissible range, upper limit (DC) | 30 V |
| Load voltage L1 |
| Rated value (AC) | 120 V |
| permissible range, lower limit (AC) | 6 V |
| permissible range, upper limit (AC) | 132 V |
| permissible frequency range, lower limit | 47 Hz |
| permissible frequency range, upper limit | 63 Hz |
| Input current |
| from supply voltage L1, max. | 160 mA |
| Power loss |
| Power loss, typ. | 15.1 W |
| Digital inputs |
| Number of digital inputs | 8 |
| Input characteristic curve in accordance with IEC 61131, type 2 | Yes |
| Input voltage |
| Rated value (AC) | 120 V |
| for signal "0" | 0V AC to 20V AC |
| for signal "1" | 74V AC to 132V AC |
| Input current |
| for signal "0", max. (permissible quiescent current) | 4 mA; 0 to 4 mA |
| for signal "1", typ. | 9 mA; 9 to 27 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| — at "0" to "1", min. | 2 ms |
| — at "0" to "1", max. | 14 ms |
| — at "1" to "0", min. | 6 ms |
| — at "1" to "0", max. | 25 ms |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 600 m |
| Digital outputs |
| Number of digital outputs | 8 |
| Controlling a digital input | Yes |
| Size of motor starters according to NEMA, max. | Size 5 to NEMA (up to 40 °C); size 4 to NEMA (up to 60 °C) |
| Switching capacity of the outputs |
| on lamp load, max. | 50 W |
| Output voltage |
| Rated value (AC) | 120 V |
| for signal "1", min. | L+ (-1 V) |
| Output current |
| for signal "1" permissible range, min. | 10 mA |
| for signal "1" permissible range, max. | 2 A |
| for signal "0" residual current, max. | 0 mA |
| Output delay with resistive load |
| "0" to "1", max. | 10 ms |
| Parallel switching of two outputs |
| for uprating | No |
| for redundant control of a load | Yes |
| Switching frequency |
| with resistive load, max. | 10 Hz |
| with inductive load, max. | 0.5 Hz |
| on lamp load, max. | 1 Hz |
| Total current of the outputs (per group) |
| horizontal installation |
| — up to 40 °C, max. | 2 000 mA |
| — up to 60 °C, max. | 1 000 mA |
| all other mounting positions |
| — up to 40 °C, max. | 1 000 mA |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 600 m |
| Encoder |
| Connectable encoders |
| 2-wire sensor | Yes |
| Interfaces |
| PROFIBUS DP |
| Transmission rate, max. | 6 000 kbit/s |
| SYNC capability | Yes |
| FREEZE capability | Yes |
| Direct data exchange (slave-to-slave communication) | Yes |
| Protocols |
| Bus protocol/transmission protocol | PROFIBUS DP |
| Interrupts/diagnostics/status information |
| Alarms | No |
| Diagnostics function | Yes |
| Diagnostics indication LED |
| Bus fault BF (red) | Yes |
| Status indicator digital input (green) | Yes |
| Status indicator digital output (green) | Yes |
| Monitoring 24 V voltage supply ON (green) | Yes |
| Potential separation |
| between PROFIBUS DP and all other circuit components | Yes |
| Potential separation digital inputs |
| between the channels | Yes |
| between the channels and PROFIBUS DP | Yes |
| Potential separation digital outputs |
| between the channels | Yes |
| between the channels and PROFIBUS DP | Yes |
| Isolation |
| Isolation tested with | 1500 V AC |
| Degree and class of protection |
| IP degree of protection | IP20 |
| Ambient conditions |
| Ambient temperature during operation |
| horizontal installation, min. | 0 °C |
| horizontal installation, max. | 60 °C |
| Air pressure acc. to IEC 60068-2-13 |
| permissible range, lower limit | 795 hPa |
| permissible range, upper limit | 1 080 hPa |
| Relative humidity |
| Operation, min. | 5 % |
| Operation, max. | 95 % |
| Vibrations |
| Operation, tested according to IEC 60068-2-6 | Yes |
| Shock testing |
| tested according to IEC 60068-2-27 | Yes |
| Connection method |
| Design of electrical connection for the inputs and outputs | Screw-type and spring-loaded terminals, permanent wiring; standard: 2-wire connection, optional: 3 and 4-wire connection |
| Dimensions |
| Width | 145 mm |
| Height | 61 mm |
| Depth | 85.5 mm |
| Weights |
| Weight, approx. | 322 g |
| last modified: | 03/13/2019 |
