| ***Spare part*** SIPLUS ET 200M IM 153-2 -25...+60°C according to EN 50155 with conformal coating based on 6ES7153-2BA02-0XB0 |
| General information |
| Vendor identification (VendorID) | 801Eh |
| Supply voltage |
| Rated value (DC) | |
| 24 V DC | Yes; A power supply according to EN 50155 shall be used |
| permissible range, lower limit (DC) | 20.4 V |
| permissible range, upper limit (DC) | 28.8 V |
| external protection for power supply lines (recommendation) | 2,5 A |
| Mains buffering |
| Mains/voltage failure stored energy time | 5 ms |
| Input current |
| Current consumption, max. | 600 mA |
| Inrush current, typ. | 3 A |
| I²t | 0.1 A²·s |
| Output voltage |
| Rated value (DC) | 5 V |
| Output current |
| for backplane bus (5 V DC), max. | 1.5 A |
| Power loss |
| Power loss, typ. | 5.5 W |
| Address area |
| Addressing volume |
| Inputs | 244 byte |
| Outputs | 244 byte |
| Hardware configuration |
| Number of modules per DP slave interface, max. | 12 |
| Time stamping |
| Accuracy | 1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules |
| Number of message buffers | 15 |
| Messages per message buffer | 20 |
| Number of stampable digital inputs, max. | 128; Max. 128 signals/station; max. 32 signals/slot |
| Time format | RFC 1119 |
| Time resolution | 0.466 ns |
| Time interval for transmitting the message buffer if a message is present | 1 000 ms |
| Time stamp on signal change | rising / falling edge as signal entering or exiting |
| Interfaces |
| Transmission procedure | RS 485 |
| PROFIBUS DP |
| Node addresses | 1 to 125 permitted |
| automatic detection of transmission rate | Yes |
| Output current, max. | 70 mA |
| Transmission rate, max. | 12 Mbit/s |
| SYNC capability | Yes |
| FREEZE capability | Yes |
| Direct data exchange (slave-to-slave communication) | Yes; Sender |
| Design of electrical connection of PROFIBUS interface | 9-pin sub D |
| 1. Interface |
| PROFIBUS DP slave |
| GSD file | SI04801.GSG |
| automatic baud rate search | Yes |
| Protocols |
| Bus protocol/transmission protocol | PROFIBUS DP to EN 50170 |
| Protocols (Ethernet) |
| TCP/IP | No |
| Potential separation |
| Potential separation exists | Yes |
| Isolation |
| Isolation tested with | 500V AC for 1 minute |
| Degree and class of protection |
| IP degree of protection | IP20 |
| Standards, approvals, certificates |
| CE mark | Yes |
| UL approval | Yes; File E239877 |
| FM approval | Yes; CofC 3028431 |
| RCM (formerly C-TICK) | Yes |
| KC approval | Yes |
| EAC (formerly Gost-R) | Yes |
| Railway application |
| EN 50155 | Yes; Sections 4, 5 and 12; no further agreements apply; T1, Category 1, Class A/B |
| Ambient conditions |
| Ambient temperature during operation |
| min. | -25 °C; = Tmin |
| max. | 60 °C; = Tmax; the rated temperature range of -25 ... +55 °C (T1) applies for the use on railway vehicles according to EN50155 |
| Ambient temperature during storage/transportation |
| min. | -40 °C |
| max. | 70 °C |
| Altitude during operation relating to sea level |
| Ambient air temperature-barometric pressure-altitude | Tmin ... Tmax at 1 080 hPa ... 795 hPa (-1 000 m ... +2 000 m) // Tmin ... (Tmax - 10 K) at 795 hPa ... 658 hPa (+2 000 m ... +3 500 m) // Tmin ... (Tmax - 20 K) at 658 hPa ... 540 hPa (+3 500 m ... +5 000 m) |
| Relative humidity |
| With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) |
| Resistance |
| Use in stationary industrial systems |
| — to biologically active substances according to EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request |
| — to chemically active substances according to EN 60721-3-3 | Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! |
| — to mechanically active substances according to EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! |
| Configuration |
| Configuration software |
| STEP 7 | Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file |
| Dimensions |
| Width | 40 mm |
| Height | 125 mm |
| Depth | 117 mm |
| Weights |
| Weight, approx. | 360 g |
| last modified: | 03/13/2019 |
