| SIPLUS ET 200S EM 4 AI I 2-wire -25...+70°C with conformal coating based on 6ES7134-4GD00-0AB0 . "Electronic module 4-20 mA; 13" bit 15 mm width, for 2-wire transducer Cycle time 40 ms/module with SF LED (group fault) |
| Supply voltage |
| Load voltage L+ |
| Rated value (DC) | 24 V; From power module |
| Reverse polarity protection | Yes |
| Input current |
| from load voltage L+ (without load), max. | 125 mA |
| from backplane bus 3.3 V DC, max. | 10 mA |
| Output voltage |
| Power supply to the transmitters |
| present | Yes |
| short-circuit proof | Yes; approx. 200 mA for module |
| Power loss |
| Power loss, typ. | 0.6 W |
| Address area |
| Address space per module |
| Address space per module, max. | 8 byte |
| Analog inputs |
| Number of analog inputs | 4 |
| permissible input current for current input (destruction limit), max. | 30 mA; limited electronically |
| Cycle time (all channels) max. | 40 ms; 33 to 40 ms |
| Input ranges (rated values), currents |
| 4 mA to 20 mA | Yes; Into 25 Ohm |
| Cable length |
| shielded, max. | 200 m |
| Analog value generation for the inputs |
| Measurement principle | integrating |
| Integration and conversion time/resolution per channel |
| Resolution with overrange (bit including sign), max. | 13 bit; 4 to 20 mA: 13 bit |
| Integration time, parameterizable | Yes |
| Integration time (ms) | 16,67 / 20 ms |
| Interference voltage suppression for interference frequency f1 in Hz | 50 / 60 Hz |
| Smoothing of measured values |
| parameterizable | Yes; in 4 stages |
| Step: None | Yes; 1x cycle time |
| Step: low | Yes; 4x cycle time |
| Step: Medium | Yes; 16x cycle time |
| Step: High | Yes; 32x cycle time |
| Encoder |
| Connection of signal encoders |
| for current measurement as 2-wire transducer | |
| — Burden of 2-wire transmitter, max. | 750 Ω |
| Errors/accuracies |
| Linearity error (relative to input range), (+/-) | 0.01 % |
| Temperature error (relative to input range), (+/-) | 0.003 %/K |
| Crosstalk between the inputs, min. | -50 dB |
| Repeat accuracy in steady state at 25 °C (relative to input range), (+/-) | 0.05 % |
| Operational error limit in overall temperature range |
| Current, relative to input range, (+/-) | 0.5 % |
| Basic error limit (operational limit at 25 °C) |
| Current, relative to input range, (+/-) | 0.3 % |
| Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency |
| Series mode interference (peak value of interference < rated value of input range), min. | 70 dB |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) | No |
| Interrupts/diagnostics/status information |
| Diagnostic messages |
| Wire-break | Yes; Measuring range 1 to 5 V only |
| Group error | Yes |
| Overflow/underflow | Yes |
| Diagnostics indication LED |
| Group error SF (red) | Yes |
| Parameter |
| Remark | 7 byte |
| Diagnostics wire break | 1 |
| Measurement type/range | 1 |
| Group diagnostics | 1 |
| Overflow/underflow | 1 |
| Potential separation |
| Potential separation analog inputs |
| between the channels | No |
| between the channels and backplane bus | Yes |
| Between the channels and load voltage L+ | No |
| Isolation |
| Isolation tested with | 500 V DC |
| Standards, approvals, certificates |
| CE mark | Yes |
| Ambient conditions |
| Ambient temperature during operation |
| min. | -25 °C; = Tmin |
| max. | 70 °C; = Tmax |
| Altitude during operation relating to sea level |
| Installation altitude above sea level, max. | 5 000 m |
| Ambient air temperature-barometric pressure-altitude | Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) // Tmin ... (Tmax - 10 K) at 795 hPa ... 658 hPa (+2 000 m ... +3 500 m) // Tmin ... (Tmax -20 K) at 658 hPa ... 540 hPa (+3 500 m ... +5 000 m) |
| Relative humidity |
| With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) |
| Resistance |
| Use in stationary industrial systems |
| — to biologically active substances according to EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request |
| — to chemically active substances according to EN 60721-3-3 | Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust, * |
| Use on ships/at sea |
| — to biologically active substances according to EN 60721-3-6 | Yes; Class 6B2 mold and fungal spores (excluding fauna); Class 6B3 on request |
| — to chemically active substances according to EN 60721-3-6 | Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-6 | Yes; Class 6S3 incl. sand, dust; * |
| Remark |
| — Note regarding classification of environmental conditions acc. to EN 60721 | * The supplied plug covers must remain in place over the unused interfaces during operation! |
| Dimensions |
| Width | 15 mm |
| Height | 81 mm |
| Depth | 52 mm |
| Weights |
| Weight, approx. | 40 g |
| last modified: | 03/13/2019 |
